Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
Forward bumpers
Forward part of the car
Cowl
Wings
Молдинги
Doors
External rear-view mirrors
The forward and back has flown down
Cover of a luggage carrier at a sedan
Back door of the versatile person
Back bumper
The sdvizhnoj hatch
Procleaning of apertures for a water drain
The control of anticorrosive protection of the bottom of a body
Salon
Seats
+ Search of malfunctions
+ Specifications
|
Молдинги
Removal of lobbies молдингов
|
|
Молдинг on a forward wing: to remove facing of a wheel niche.
From the interior of a wing to turn on шестигранную a nut.
To shift молдинг back and to remove from a wing.
Молдинг on a lateral part behind (a back wing): to warm up молдинг the hair dryer to temperature approximately 40С.
Then to take out молдинг from a fixing percussion cap the screw-driver which has been wrapped up in a rag.
At installation to insert молдинг in fixing клипсу and in addition to paste (for example as it is described more low or in the help).
Молдинги on doors: to disconnect an overlay from a glutinous layer.
In most cases it can be made, only heating молдинг the hair dryer approximately to temperature 40С, but also in this case more often the overlay does not manage to be removed the intact. Therefore it is necessary to take care of the new.
If at your car a new varnish covering: to clear a place on a door where it will be pasted молдинг, gasoline and удалителем silicone.
Otherwise on a door with an old covering. You should remove the glue rests, having left about 1 mm of a thickness. This rest is necessary as a basis for new клеющего a material.
Watch thus not to damage a varnish covering.
To clear a place on a door where it will be pasted молдинг.
Plastic parts in the field of gluing to wipe cleaner D 009 400 01 and to wipe dry.
Metal (only in case on metal a new varnish covering) and plastic elements of a body to cover in the field of gluing by a first coat. For metal parts to apply праймер D 009 200 02, to plastic D 009 600.
To put on an underside молдингов клеющий hermetic AKD 476 KD5 05 from PUR – in the middle молдинга the layer suffices gluing thickness of 4 mm.
To put молдинг to a door, to correct and densely to press in a gluing place – especially the ends.
Hardening time at 20С: 4 hours.
|
|
|
|
The help: if the procedure written under instructions Audi seems too difficult, it is possible to arrive as follows: to put a thick layer on an underside молдинга transparent silicone hermetic. To press молдинг on the cleared overlay of a door and to clean superfluous hermetic. Before hermetic drying (about one day) to fix молдинг клеющей a tape. In this case молдинг keeps though and not so it is good, as serial, but nevertheless quite maintains an automatic sink. |
The bottom protective overlay
On a bottom edge of doors, and also by adjoining metal parts on the corresponding version of the car there passes a thin protective overlay. More low the removal plan.
|
|
The parts of an overlay which are on forward wings and on back lateral parts, are pasted. Removal and installation are described in section Removal молдинга.
To disconnect from молдингов on doors forward and back tips and, at an open door, to remove молдинг from a percussion cap to (pull out).
|
|
|
|
