Audi 80/Avant (B4)

Since 1991-1995 of release

Repair and car operation



Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
   Forward bumpers
   Forward part of the car
   Cowl
   Wings
   Молдинги
   Doors
   External rear-view mirrors
   The forward and back has flown down
   Cover of a luggage carrier at a sedan
   Back door of the versatile person
   Back bumper
   The sdvizhnoj hatch
   Procleaning of apertures for a water drain
   The control of anticorrosive protection of the bottom of a body
   Salon
   Seats
+ Search of malfunctions
+ Specifications


a13f00c7

Salon

Removal of the left shelf

For shelf removal at the left to weaken bolts with 2 on 5. At installation to insert a shelf ahead in directing (the position 1 shows one of them).

The left bottom part of a covering of the instrument panel, integrated with a shelf, should be removed almost in all cases when access to an underside of the instrument panel is necessary.

 PERFORMANCE ORDER

    Narrow face key to turn out four screws round a shelf. A few to cast away a shelf downwards and to extend to itself. At installation to insert a covering first line in both cars directing on the bottom and near pedals. Not too hardly to tighten screws.

Removal of a ware box

The ware box (2 and 3) is attached (1) loops to the instrument panel (arrow). On an illustration the box is shown in the disassembled kind.


 PERFORMANCE ORDER

    To turn out on a bottom edge instrument both panels of the fixing screw of a loop of a ware box. Slightly to wring out stoppers of a ware box inside and to cast away a ware box downwards.

Removal of the bottom part of the central console

Removal of a back part of the central console: to remove a lath (1), to disconnect a covering of the lever of a lay brake (3), to disconnect an earring (arrows) on the handle (2) from a clamp.


 PERFORMANCE ORDER

    To tighten a lay brake. To wring out a screw-driver fixing linings of a cover of the lever of a lay brake and to separate from a floor. In front slightly to raise a covering, to wring out a lever earring upwards and to extend the lever forward. To raise the decorative panel in front of the lever of a lay brake. Thus to hook an upper edge a small screw-driver. To turn out six fixing bolts, being under the panel. To remove a back ashtray. To turn out under an ashtray two шестигранных a bolt. To pull a console part for a first line upwards and to remove it in a direction forward over the lever of a lay brake.

Removal of a forward part of the central console

Removal of a forward part of the central console: to turn off a head of the lever of a gear change (2), to weaken a bolt on a casing of the lever (1). (3) – lobbies directing.


Arrows show on two bolts located in cut of the panel of heating which are necessary for weakening for removal of the central console.


 PERFORMANCE ORDER

    To disconnect a wire on "weight" of the accumulator. Completely to remove a back part of the central console. To remove the lever of a gear change or the selector lever. To turn away a bolt with crosswise шлицем on back to edge of the console and to remove a cover of the handle of a gear change or a covering. To disconnect all three regulators of heating/ventilation. To turn away two screws of the panel of heating and to remove it. At the cars equipped with the automatic conditioner, completely to remove a control panel. Below on the right and at the left in cut of the panel of heating to turn out on one screw. To wring out the console with an ashtray downwards, at a variant of a body with additional devices to remove in a direction downwards a narrow decorative plate. In a direction to disconnect the console from a control panel back. If necessary to disconnect wires. At installation directing on the instrument panel and the central console should enter one into another.